What's new in CLiq 2.0.6.82
Jun 16, 2016
- Fixed a bug when importing CPT files and all points are marked as non liquefiable.
New in CLiq 1.7.6.49 (Jun 16, 2016)
- Added option for CRR calculation based on custom PL (applies only to Moss et al. and B&I 2014 methods).
- Fixed a bug with custom report page and B&I (2014).
New in CLiq 1.7.6.34 (Jun 16, 2016)
- Latest Boulanger & Idriss CPT based method added.
- New ground improvement control module added.
- Added filter to eliminate negative raw data values.
- Extended NCEER method to perform calculations for Qtn,cs up to 200.
- New probabilistic settlements module added.
- Fixed an issue with the calculation of rd with I&B 2008 (using Imperial units).
- Various minor issues fixed.
- New updated manual.
New in CLiq 1.7.5.27 (Jun 16, 2016)
- Users can now switch between LPI or LSN by left clicking on the LPI plot.
- Application will search for system defined temporary folder to be used for the creation of reports.
- Aging factor now applies to SPT and Vs assessment modules.
- Fixed an issue with Vs Kayen et al. report file.
- Fixed an issue with Vs assessment module reseting the “Can liquefy” state after calculation.
- Fixed an issue with overburden correction factor for I&B method.
- Fixed an issue with the calculation of CN for I&B.
New in CLiq 1.7.4.34 (Jun 16, 2016)
- Added two additional parametric calculations.
- Added calculation log text report.
- Added custom report page creation.
- Added option to use any MSF (NCEER, Moss et al., Idriss & Boulanger) regardless the selected assessment method.
- Added option not to display numeric results for CPT points on the 2D map.
- Fixed a bug with strain plot not displaying results correctly.
- Fixed an issue with importing files from CLiq project files.
- Lowered maximum volumetric strain value for dry sands settlements.
New in CLiq 1.7.1.14 (Jun 16, 2016)
- Added option to save/apply plot scale values.
- Fixed a bug where imported CPeT-IT files could not display correct depth.
New in CLiq 1.7.1.6 (Jun 16, 2016)
- Added Idirss & Boulanger 2008 calculation method.
- Columns in tabular results can now be resized.
- Added aging factor in volumetic strain calculation.
- Added option to apply probability of liquefaction to volumetric strain.
- Added option to define non-hysrostatic piezometric profiles to in situ and during earthquake GWT.
- Fixed a bug in the calculation of LPI and settlements of the very first CPT point when a fill is defined.
New in CLiq 1.5.1.26 (Jun 16, 2016)
- Added Idirss & Boulanger 2008 calculation method.
- Columns in tabular results can now be resized.
- Added aging factor in volumetic strain calculation.
- Added option to apply probability of liquefaction to volumetric strain.
- Added option to define non-hysrostatic piezometric profiles to in situ and during earthquake GWT.
- Fixed a bug in the calculation of LPI and settlements of the very first CPT point when a fill is defined.
New in CLiq 1.5.1.16 (Jun 16, 2016)
- Added SPT and Vs based liquefaction assessment methods for direct comparison with CPT based method.
- Added option to include custom CSR data.
- Added option to define custom Y axis scale for overall results report.
- Starting with this version, for network based licenses a special version of the software will be delivered upon request.
New in CLiq 1.4.1.22 (Jun 16, 2016)
- Enabled Moss et al. (2006) method for the calculation of FS against soil liquefaction.
- Added option to define start page number when printing overall reports.
- Added a simple report page in the parametric analysis tool.
- New appearance in tabular results report pages.